LumPi Panda
Retro Guru
- Feedback
- View
Your wife sounds a lot like my wife...
Yeti build thread. Not in the wrong section.
- Thread starter LumPi Panda
- Start date
Added on singletrack
https://singletrackworld.com/forum/topic/yeti-build-with-a-te/
https://singletrackworld.com/forum/topic/yeti-build-with-a-te/
LumPi Panda
Retro Guru
- Feedback
- View
Thanks Stevet1, does this mean I've "gone viral", as the youth say?
I haven't been viral since Covid-19.
LumPi Panda
Retro Guru
- Feedback
- View
Spring has sprung.
Brass wire wound into a spring...
Limit screws, bolts and the like will be added later.
A sense of scale.
LumPi Panda
Retro Guru
- Feedback
- View
This is the smallest jig on the build. It's for building the sprung jaws on the pedals.
More springs. These were a bit fiddly to assemble.
LumPi Panda
Retro Guru
- Feedback
- View
Final dry assembly before getting the glue out.
I need to sort out a box for it before sticking it together. Once the stem is glued in place it wont fit in the toolbox that I've been using up until now.
LumPi Panda
Retro Guru
- Feedback
- View
I see someone on Singletrack has questioned the "cheatingness" of laser cutting vs. 3D printing.
The way I look at it is this;
A laser cutter cuts shapes out of a flat sheet of material. Once these pieces are cut, there is still assembly and filler/fettling to be done.
Essentially all the laser is doing is cutting bits out that theoretically could be cut and filed by hand but would take ages. It saves an awful lot time, a bit like using an electric drill instead of a brace and bit, or combine harvester vs. scythe.
A 3D printer, on the other hand, makes stuff. Simple as that. You press a button and some time later you have a fully realised 3D part that only requires a certain amount of surface finishing. I have nothing against 3D printers or 3D printing, in fact I think it's brilliant and use it an increasing amount in my professional work. What is particularly exciting about it is how it allows you to make things that would be impossible to make any other way.
In a nutshell, it's a bit like painting a picture vs. taking a photograph. There are some tremendous photographs that require a great deal of skill, knowledge and preparation, but it is a different route to the end result to a painting.
The way I look at it is this;
A laser cutter cuts shapes out of a flat sheet of material. Once these pieces are cut, there is still assembly and filler/fettling to be done.
Essentially all the laser is doing is cutting bits out that theoretically could be cut and filed by hand but would take ages. It saves an awful lot time, a bit like using an electric drill instead of a brace and bit, or combine harvester vs. scythe.
A 3D printer, on the other hand, makes stuff. Simple as that. You press a button and some time later you have a fully realised 3D part that only requires a certain amount of surface finishing. I have nothing against 3D printers or 3D printing, in fact I think it's brilliant and use it an increasing amount in my professional work. What is particularly exciting about it is how it allows you to make things that would be impossible to make any other way.
In a nutshell, it's a bit like painting a picture vs. taking a photograph. There are some tremendous photographs that require a great deal of skill, knowledge and preparation, but it is a different route to the end result to a painting.
27motorhead
Old School Grand Master
- Feedback
- View
This is the issue with sharing stuff on the net. Be prepared for some uneducated dumb-arse comments from keyboard warriors who look at something for 5min if that. 
Without a laser cutter I dread to think how long this would have taken! There is no disputing you have the skills...
Without a laser cutter I dread to think how long this would have taken! There is no disputing you have the skills...
LumPi Panda
Retro Guru
- Feedback
- View
This is the issue with sharing stuff on the net. Be prepared for some uneducated dumb-arse comments from keyboard warriors who look at something for 5min if that.
Without a laser cutter I dread to think how long this would have taken! There is no disputing you have the skills...
I think "dumb-arse" and "keyboard warrior" might be a little strong. Uneducated, yes, but hopefully now educated.
I hope my previous post doesn't come across as taking the hump, it was not intended as such.
To be honest, without a laser cutter I doubt it would have even occured me to make this.
27motorhead
Old School Grand Master
- Feedback
- View
This forum is friendlier than most, so you're pretty safe here.I think "dumb-arse" and "keyboard warrior" might be a little strong. Uneducated, yes, but hopefully now educated.
I hope my previous post doesn't come across as taking the hump, it was not intended as such.
To be honest, without a laser cutter I doubt it would have even occured me to make this.
Your post was super informative and was a great explanation of the process.
The phrase 3D printing is chucked about a lot, but even that process in itself isn't straight forward with setting up and post print cleaning up. Not to mention all the various methods/machines you can use depending on time/material/budget.
Keep up the great work/posts!
Similar threads
