THIS THREAD IS OVER!!!

[Dead Rats]

Here's a bunch of stuff that's all under £18 and replaces all my previous FS threads... all prices include postage in UK, packaged with usual Dead Rats' finesse payment by PayPal gift as per... plus I'm working from home this week so hopefully we can beat the imminent PO union strike!!!

By the way, I am looking to buy:
16 hole rear road hub (for 9 speed Shimano)

Here we go:

Seatposts
L>R
Kalloy 25.4mm x 310mm, bit scratched, £6
Kalloy 26.8mm x 260mm, very scratched, £4 / SOLD
Ritchey 27.2mm x 220mm, cut down and scratched, £6 / SOLD
fake Syncros 30.9mm x 370mm, slight play where clamp meets shaft but usable, £4 / SOLD

8 speed Acera rear mech, scratched but ok, £5 / GONE


NOS Tourney 5 speed SIS shifter, cable & crimp, boxed, £6

Azonic Head Lock silver, £8 (does away with ahead star nut and top cap)
LONG MODEL - 210-240mm approx - SOLD!


used DMR STS arm and roller, £5 / SOLD


brand new DMR STS roller, £4 / SOLD


31.8mm seatpost clamp, single bolt, £3 / GONE


blue 31.8mm seatpost QR clamp, £4

new star-fangled nut from Ritchey Logic aheadset, £2

1 1/8" carbon spacers, 10mm & 5mm, £3

1 1/8" Kore spacers, 3 x 5mm, £3 / SOLD


2 pairs of 1" rigid threaded forks with canti / v-brake bosses, both have been powder coated and are unused since, mint, finish is superb, £17 each posted
LEFT:
1" threaded rigid steel forks (Raleigh?)
for v-brake or canti (three spring holes)
142mm steerer, top 33mm is threaded
395mm crown race to axle
two sets of eyelets

RIGHT - SOLD!
1" threaded rigid steel forks, unsure of brand
for v-brake or canti (three spring holes)
134mm steerer, top 21mm is threaded - ie they've been cut down but carefully
395mm crown race to axle
one set of eyelets

Zoom Gordo forks, £18 posted (they're heavy!)

Marin top cap, £2

Michelin 2.2 DH tyre, £12 posted - GONE


Hutchinson 2.1 DH tyre, £13 posted

 

[big.eck]

hi al , what size is the michelin tyre ?

 

[Dead Rats]

hi al , what size is the michelin tyre ?

easy Alex, it's 2.2 (54 x 559) - post amended

 

[big.eck]

if only it was a 2.4 upwards........... i just missed out on a 2.8 one of these and i'm quite gutted about it...

cheers anyway

 

[Dead Rats]

if only it was a 2.4 upwards........... i just missed out on a 2.8 one of these and i'm quite gutted about it...

cheers anyway

this for your tractor is it?

 

[big.eck]

the other tractor yes i need a 2.4/5 for the rear and a 2.7/8 for the front

i'm 19 odd stone and like to throw my bikes about a bit

 

[Dead Rats]

the other tractor yes i need a 2.4/5 for the rear and a 2.7/8 for the front

i'm 19 odd stone and like to throw my bikes about a bit

hence the Ameoba bars then! my Marin weighs about the same as you now but damn comfy!

 

[fatandforty]

Hi

Whats the tube length of the forks?

Mike

 

[Dead Rats]

Hi

Whats the tube length of the forks?

Mike

LEFT:
1" threaded rigid steel forks (Raleigh?)
for v-brake or canti (three spring holes)
142mm steerer, top 33mm is threaded
395mm crown race to axle
two sets of eyelets

RIGHT:
1" threaded rigid steel forks, unsure of brand
for v-brake or canti (three spring holes)
134mm steerer, top 21mm is threaded - ie they've been cut down but carefully
395mm crown race to axle
one set of eyelets

post amended as above... you want a close up pic as the photo does not do their finish justice - and note how p/coater masked off bosses, threads and crown race area after sand-blasting

 

[WD Pro]

What diameter are the carbon spacers please ?

WD