Foes Weasel 1996

Dami

Retro Guru
Feedback
View
One longtime project has moved forward a bit. Found this well used Foes Weasel -96 from our local classifieds here about 1.5 years ago and it's been slowly brewing in my mind. It had a history of all use no maintenance so had the basic struggles with the stuck seatpost etc., but the biggest issue with it was definitely the main pivot area where the other rear end tightening bolt had been snapped and it had been used with loose connection. This meant that I had to remove the cut bolt and also put some filling on the worn side of the main axle to allow keeping the rear tightly connected to it. These came with the delrin bushings back in the day, but I believe there was also some aftermarket bearing kit available for them. The sliding surfaces on this were still in good condition, so I didn't have to replace any pivot components.

p5pb21189959.jpg


I also tried to refresh the worn dark purple cooks by stealing the wife's oven cleaner, giving them a good scrub, polishing them and putting decals on them. Found cheap repro caps on them also that fit them nicely.

p5pb21189976.jpg


This summer I finally got the frame painted and put it all together. It originally had the rarer Kuster shock on it, which I was planning on servicing, but apparently there is no separate nitrogen filling port so its service is a total PITA and would require fabricating some special tool for it (I believe Risse Racing has made one but sending it over there and back would be too expensive). One other interesting component on it was the Bici made titanium seatpost, that I didn't find too much info on. I believe Bici was a smaller US brand that made also nice hubs, but if someone knows more about it please share your wisdom!

Rehauled the Judy DH for it and had the Ringle bash guard in my boxes, but still have to build the wheels and install silver CK headset on it when it arrives from a friend. Wheels will probably be silver Sunrims CR18s on silver Pulstars and also planning on installing the Bullet Bros chain tensioner here as it would fit the period and build quite nicely. Also the decals are slowly on their way. But step by step!

p5pb21189956.jpg


p5pb21189955.jpg


p5pb21189954.jpg


p5pb21189953.jpg


p5pb21189957.jpg


p5pb21189958.jpg
 
Last edited:
Nice work it looks great so far.

Is the fork steerer going to be long enough once you have the headset installed?
 
Nice work it looks great so far.

Is the fork steerer going to be long enough once you have the headset installed?
That’s a valid point that I haven’t considered yet, just threw the azonic shorty stem on it. My other similar CK has stack height of about 30mm and there’s about 20mm steerer shown, so it might be a bit short. Have to measure properly when the headset arrives and maybe have to use another stem there! Too bad as this would’be been nice here..
 
Due to the international shortages of parts, I've been waiting for suitable length straight pull spokes to pop up somewhere, and managed to order some about a week ago. So the project's been on hold, but will get to start building the wheels when the spokes arrive! The wheelset and brakes will be Sun Rhyno Lites on Pulstar hubs and some Magura Johnny T's with ADP carbon arches.

@Baulz had a good point before about the steerer length. The Azonic Shorty is so high in profile that I had to go for a lower BMX style stem instead. Hopefully will get it finished during the Spring!
 
About a week ago I got a very unexpected offer as one fellow biker was dropping some small bits to my workshop and stayed for a while checking some of the bikes. After a long chat he said that he’d have a set of Shimano Airlines that wasn’t currently working and had been waiting a long time on his shelves. For me those have always been pure unobtainium, but due to the fact the set wasn’t working, and that I promised to try and get it back running, I got a very good deal on it.

After checking the set and taking apart the rear derailleur, I found the reason for the problems. There was a short transfer cable cut that has to be replaced but otherwise everything else is looking really good!

154121D9-08F4-43FE-B295-E29889521677.jpeg

The frame has now new decals on and the short steerer tube issue was solved with a BMX stem, so next just have to start building the wheels and sourcing/fabricating the new cable for the derailleur!

0648BAAC-28FA-4107-A7E9-025AE5DC7DB2.jpeg

One of the Shimano Airlines bikes that was used to test the prototypes in the late 90’s was a Weasel so it felt fitting putting the set on this project.
 

Latest posts

Back
Top